KME JewelStik 1-2-3 Diamond Hone – Oldawan
KME JewelStik 1-2-3 Diamond Hone – Oldawan
KME Hewlett JewelStick 1-2-3 Diamond Hone (Manufacturer Part # JLSTK) Size: 1" x 4" x 3/16" Trying to figure out how to sharpen a blade with a tighter inside radius than your flat stones will handle? Here’s an awesome accessory diamond hone to add to your KME knife sharpening kit. This hone set includes the 3 sided.
KME Hewlett JewelStick 1-2-3 Diamond Hone
(Manufacturer Part # JLSTK)
Size: 1 x 4 x 3/16
Trying to figure out how to sharpen a blade with a tighter inside radius than your flat stones will handle? Here’s an awesome accessory diamond hone to add to your KME knife sharpening kit.
This hone set includes the 3 sided hone and rod only. It can be used with your KME Sharpener - purchased separately - or free hand.
The curved surfaces of this hone are perfectly suited for sharpening recurve blades, hawkbill blades, Karambits, Kukris, or any other knife or broadhead with a concave cutting edge (inside curve) design.
Custom made in the USA for KME by Hewlett MFG, it has 3 different diamond grit hones on it - Coarse (270), Medium (600), & Fine (1800). Each hone has a 1/2 wide rounded diamond sharpening surface making it perfect for sharpening even the most extreme concave blade designs.
For easy use on your KME sharpener it includes a guide rod which attaches to the hone with a close tolerance friction fit. Just push the rod a few inches into the hone and you are ready to fit it through the spherical bearing on your sharpener - there is no need to push the rod completely through to the other end of the hone though some people find that more comfortable. The rod can be installed in either end of the hone so that the entire diamond surface can be utilized.
Please note that the caps on both ends of the hone are duplicates so only one end will show the grits correctly - you can mark that end cap or file off the markings on the other end.
A note about rounded hones: When using rounded hone, care must be taken not to round over the tips of your knives. This is because unlike a wide flat stone, a rounded hone has a very small area of blade contact. It is easy to go just a bit too far and slip past the tip which will cause the point or tip to be deformed or rounded over slightly. You can be fairly aggressive throughout the length of the blade but be very careful when you sharpen the tip section..
Also suitable to be used free hand
(does NOT include the knife sharpening system, knife or the base shown in the secondary pictures.)
HEWLETT JEWELSTIK HMK123 Diamond Coarse Medium Fine 3 side knife
GrizzlyStik Sharpening Kit From KME Sharpeners, 53% OFF
Josie 8 Carat Oval Cut Earth Mined VVS1 Diamond Engagement Ring in 18k
Hewlett JewelStik 12 Diamond Knife Sharpener Three-Step System
KME Gold Series Diamond Hones
KME Knife Sharpener with 4 Diamond Stones - Used. Save $90. (This is the last one.) , The KME Diamond Knife Sharpener is used. The stones do not even
KME Diamond Knife Sharpener - Used
KME Precision Knife Sharpening System KF-D4 with Base - with 4 KME
Hewlett JewelStik Professional 1-2-3, 10 Diamond Sharpening Rod
14K 3 Stone Diamond Necklace. Kay Jewelers. 1 ct. Wom… - Gem
GrizzlyStik Sharpening Kit From KME Sharpeners, 53% OFF
Multicolor Ethiopian Opal 18K Yellow Gold Over Silver 3-Stone Ring 2.58ctw
Precision R.P.S.H. Combo Kit Knife Sharpening System KF-CBO – Oldawan