Elim a Dent 14 DeWalt LED Light (manual suction cup)

September 30,2024

3 Strip 20v PDR L.E.D.cordless 14inch light board. (2 outer cool white 1 center warm white) BATTERIES AND CHARGER SOLD SEPARATE PWM Dimmer Included USES DCB201, DCB203, DCB200, DCB204 BATTERIES OR GENERIC REPLACEMENTS "Patents 9109769, 9212793" This board is powered by Dewalt 20v lithium ion batteries or off-brand replacements. The board can be rotated and twisted 360 degrees. Comes with 3 L.E.D. strips, 1 center and 2 outer. 3 switches on base control strips. Each switch controls 1 strip of L.E.D. Batteries charge in 30-60 min and last for 4 to 10 +hours depending on how many strips you power and what size battery your using.New Spinal-Cord SetupElim A Dents Patent Pending Spinal Cord setup. These new revolutionary fittings allow you to extend and shorten your cord length without taking the entire assemble apart. Better than that each link has.
3 Strip 20v PDR L.E.D.cordless 14inch light board. (2 outer cool white 1 center warm white) BATTERIES AND CHARGER SOLD SEPARATE PWM Dimmer Included USES DCB201, DCB203, DCB200, DCB204 BATTERIES OR GENERIC REPLACEMENTS Patents 9109769, 9212793 This board is powered by Dewalt 20v lithium ion batteries or off-brand replacements. The board can be rotated and twisted 360 degrees. Comes with 3 L.E.D. strips, 1 center and 2 outer. 3 switches on base control strips. Each switch controls 1 strip of L.E.D. Batteries charge in 30-60 min and last for 4 to 10 +hours depending on how many strips you power and what size battery your using.New Spinal-Cord SetupElim A Dents Patent Pending Spinal Cord setup. These new revolutionary fittings allow you to extend and shorten your cord length without taking the entire assemble apart. Better than that each link has a bolt and nut inside a plastic housing that allows you to set the tension of each link. Ounce Spinal Cord fittings are connected they cannot pop apart without loosening the tension screws. If you prefer that loose broke in feel loosen the screws, if you like to keep that tight like new feeling tighten the screws. If you would like to have part of the links loose so you can maneuver and spin the board freely but have another section tight to support the board’s weight well you can do that also.>20v powered by Dewalt lithium ion batteries or off-brand replacements.>Allows you to use existing Dewalt chargers and batteries to eliminate carrying multiple different batteries and chargers.> Easy battery release for swapping out dead batteries> Completely cordless no exposed wires.> Versatile 360 degrees of movement with no worries of cord tangles.> Quick disconnects to easily replace wearable parts like the loc line assembly.> Up to 9 20v strips with a variety of warm/cool color combination.> 3 independent switches on base so they don't get switched by accident when adjusting board and also allow for various led strip combinations.>Matched acrylic face plate for the perfect fade. Acrylic is secured into place so it won’t slide or fall out.>Built in suction cup with replaceable plunger and pad which saves cost on repairs by only needing to purchase parts instead of entire assembly. Now works with Woods and Ram Twist Cups>Low profile dimmer on base side to control brightness of L.E.D..

3 Strip 20v PDR L.E.D.cordless 14inch light board.
(2 outer cool white 1 center warm white)
BATTERIES AND CHARGER SOLD SEPARATE
PWM Dimmer Included
USES DCB201, DCB203, DCB200, DCB204 BATTERIES OR GENERIC REPLACEMENTS
Patents 9109769, 9212793

This board is powered by Dewalt 20v lithium ion batteries or off-brand replacements. The board can be rotated and twisted 360 degrees. Comes with 3 L.E.D. strips, 1 center and 2 outer. 3 switches on base control strips. Each switch controls 1 strip of L.E.D. Batteries charge in 30-60 min and last for 4 to 10 +hours depending on how many strips you power and what size battery your using.

New Spinal-Cord Setup

Elim A Dents Patent Pending Spinal Cord setup. These new revolutionary fittings allow you to extend and shorten your cord length without taking the entire assemble apart. Better than that each link has a bolt and nut inside a plastic housing that allows you to set the tension of each link. Ounce Spinal Cord fittings are connected they cannot pop apart without loosening the tension screws. If you prefer that loose broke in feel loosen the screws, if you like to keep that tight like new feeling tighten the screws. If you would like to have part of the links loose so you can maneuver and spin the board freely but have another section tight to support the board’s weight well you can do that also.

>20v powered by Dewalt lithium ion batteries or off-brand replacements.

>Allows you to use existing Dewalt chargers and batteries to eliminate carrying multiple different batteries and chargers.

> Easy battery release for swapping out dead batteries

> Completely cordless no exposed wires.

> Versatile 360 degrees of movement with no worries of cord tangles.

> Quick disconnects to easily replace wearable parts like the loc line assembly.

> Up to 9 20v strips with a variety of warm/cool color combination.

> 3 independent switches on base so they don't get switched by accident when adjusting board and also allow for various led strip combinations.

>Matched acrylic face plate for the perfect fade. Acrylic is secured into place so it won’t slide or fall out.

>Built in suction cup with replaceable plunger and pad which saves cost on repairs by only needing to purchase parts instead of entire assembly. Now works with Woods and Ram Twist Cups

>Low profile dimmer on base side to control brightness of L.E.D.